• Document: SPECIFICATION
  • Size: 1.53 MB
  • Uploaded: 2018-11-28 12:42:11
  • Status: Successfully converted


Some snippets from your converted document:

PROPOSAL / SPECIFICATION FMSA: CHOCOLATIER / ICE-CREAM MANUFACTURE BY JASON JANSZ- SPECIFICATION CONSULTANT DATE 29/10/2015 Product Overview  Main Production & Commercial Kitchen areas / Coolrooms / Freezers: Sikafloor 22 PurCem @ 5-6mm Polyurethane cement flooring  Slip rating : R12 with B1 Bauxite non slip material  Colour: TBC  High Performance non slip  Chemical and impact resistance  10 Year Guarantee all information in this proposal is to read in conjunction with the latest Technical Data Sheets and Application Manuals Product Overview  Circulation Zones / Clean Stores : for extra point loads, trolleys, mitigation and overall longevity of system.  Sikafloor 263SL/264T Finish - 2mm Epoxy floor system  Comprised of: Primer: Sikafloor 160 @3-4m2 per mixed litre Body : Sikafloor 263SL @ 2 mixed litres per m2 Top: Sikafloor 264T @ 5-6m2 per mixed litre  Colour In approved RAL Colour Codes.  Texture To conform to R-10 and customers requirement 3-4% 60 or 80 mesh silica carbide, customer to verify sample before proceeding. *Washbays may require higher profile non slip. all information in this proposal is to read in conjunction with the latest Technical Data Sheets and Application Manuals  New Resin Coves:  Sikafloor 29 PurCem @ 5mm rendered to up stands and formed coves, Sealed with Two coats Sikafloor 31 PurCem Top Coat.  Epoxy Floor Grading: (ponding water repair)  Sikafloor 160 or Sikafloor 94 High strength epoxy mortar Mix Design not to exceed 6-1 Sand / epoxy resin ratio Install falls to comply to a minimum 1 in 100 fall – Suggest 1 in 80 falls for more efficient drainage of the floor area.  Strip Drains:  Option 1: Sikafloor 29 PurCem @ 6mm rendered to up stands and formed coves, Sealed with Two coats Sikafloor 31 PurCem Top Coat.  Option 2: Fibreglass reinforced epoxy with 2-3 top coats Sikafloor 31 PurCem all information in this proposal is to read in conjunction with the latest Technical Data Sheets and Application Manuals PREPARATION AND TERMINATION DETAIL  Production Flooring Areas  Remove existing damaged flooring material to sound substrate  Preparation to be by Scarification / Grinding / Saw cut combination  Grinding should be as such to help remove trowel marks and associated water ponding caused be trowel mark defects in existing floor  A surface profile of CSP 4-5 as a minimum should be produced. (tailored to project)  Termination Saw cuts to be cut around/along all drains, equipment, walls and edge terminations. In accordance with PurCem application manual all information in this proposal is to read in conjunction with the latest Technical Data Sheets and Application Manuals  Cracks:  Cracks are to be treated as per below detail, a bandage over the crack once repaired can be installed to aid in guarding against future cracking. (please note that structural movement of concrete can not be controlled and may be susceptible to further cracking) all information in this proposal is to read in conjunction with the latest Technical Data Sheets and Application Manuals  Terminations  All terminations of the floor to Stainless equipment to be Sikaflex Tank or Sikaflex 11 FC  Prime to stainless using Primer 210  Scuff and clean stainless - Wait for 40 minutes then apply sealant  Drains  Thickening of Sikafloor PurCem along drain edge to a depth of 10mm.  Drain / PurCem interface to be cut then sealed using Sikaflex Tank all information in this proposal is to read in conjunction with the latest Technical Data Sheets and Application Manuals  Strip and Lined Drain/Pits Termination:  Thickening of Sikafloor PurCem along drain edge to a depth of 10mm.  Drain / PurCem interface to be cut then sealed using Sikaflex Tank all information in this proposal is to read in conjunction with the latest Technical Data Sheets and Application Manuals  Concrete Kerb / Cove detail:  kerbs are to be rendered with Sikafloor 29 PurCem, key joints are to be cut at the top edge for good adhesion then sealed at the panel interface with Sikaflex 11FC food grade sealant all information in this proposal is to read in conjunction with the latest Technical Data Sheets and Application Manuals  Joints and Heat Strips  Construction joint’s to have a thickening of PurCem along edges of joint.  Re cut and caulk with Sikaflex Tank – Food grade sealant all information in this proposal is to read in conjunction with the latest Technical Data Sheets and Application Manuals QA - TESTING  On site sample to be placed for control reference – Texture and thickness  Pull off test to be c

Recently converted files (publicly available):