• Document: Lab 6.4.2: Challenge Inter-VLAN Routing
  • Size: 97.73 KB
  • Uploaded: 2019-04-16 18:21:18
  • Status: Successfully converted


Some snippets from your converted document:

Lab 6.4.2: Challenge Inter-VLAN Routing Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway (Hostname) S1 VLAN 99 192.168.99.11 255.255.255.0 192.168.99.1 S2 VLAN 99 192.168.99.12 255.255.255.0 192.168.99.1 S3 VLAN 99 192.168.99.13 255.255.255.0 192.168.99.1 R1 Fa 0/0 192.168.50.1 255.255.255.0 N/A All contents are Copyright © 1992–2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1 of 5 CCNA Exploration LAN Switching and Wireless: Inter-VLAN Routing Lab 6.4.2: - Challenge Inter-VLAN Routing R1 Fa 0/1 See Subinterface Configuration Table N/A PC1 NIC 192.168.10.21 255.255.255.0 192.168.10.1 PC2 NIC 192.168.20.22 255.255.255.0 192.168.20.1 PC3 NIC 192.168.30.23 255.255.255.0 192.168.30.1 Server NIC 192.168.50.254 255.255.255.0 192.168.50.1 Port Assignments – Switch 2 Ports Assignment Network Fa0/1 – 0/4 802.1q Trunks (Native VLAN 99) 192.168.99.0 /24 Fa0/5 – 0/10 VLAN 30 – Sales 192.168.30.0 /24 Fa0/11 – 0/17 VLAN 10 – R&D 192.168.10.0 /24 Fa0/18 – 0/24 VLAN 20 – Engineering 192.168.20.0 /24 Subinterface Configuration Table – Router 1 Router Interface Assignment IP Address Fa0/0.1 VLAN1 192.168.1.1 Fa0/0.10 VLAN 10 192.168.10.1 Fa0/0.20 VLAN 20 192.168.20.1 Fa0/0.30 VLAN 30 192.168.30.1 Fa0/0.99 VLAN 99 192.168.99.1 Learning Objectives Upon completion of this lab, you will be able to to: • Cable a network according to the topology diagram • Clear configurations and reload a switch and a router to the default state • Perform basic configuration tasks on a switched LAN and a router • Configure VLANs and VLAN Trunking Protocol (VTP) on all switches • Configure a router to support 802.1q trunking on a Fast Ethernet interface • Configure a router with subinterfaces corresponding to the configured VLANs • Demonstrate inter-VLAN routing Task 1: Prepare the Network Step 1: Cable a network that is similar to the one in the topology diagram. The output shown in this lab is based on 2960 switches and an 1841 router. You can use any current switches or routers in your lab as long as they have the required interfaces shown in the topology diagram. Other device types may produce different output. Note that Ethernet (10Mb) LAN interfaces on routers do not support trunking, and Cisco IOS software earlier than version 12.3 may not support trunking on Fast Ethernet router interfaces. Set up console connections to all three switches and to the router. All contents are Copyright © 1992–2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 2 of 5 CCNA Exploration LAN Switching and Wireless: Inter-VLAN Routing Lab 6.4.2: - Challenge Inter-VLAN Routing Step 2: Clear any existing configurations on the switches. Clear NVRAM, delete the vlan.dat file and reload the switches. Refer to Lab 2.2.1 if necessary for the procedure. After the reload is complete, use the show vlan command to confirm that only default VLANs exist and that all ports are assigned to VLAN 1. Step 3: Disable all ports using the shutdown comm

Recently converted files (publicly available):